Office: 1700 Scherer Pkwy, St Charles, MO Mon–Fri 8–6 · Sat 9–2 · Sun closed (314) 730-4080

Weather, Storms & Climate

Snow Load vs. Snow Shedding: What Illinois Homeowners Need to Plan For

Illinois homeowners need two separate winter plans: one for the weight a roof may carry and another for where snow and ice may slide. This guide explains how structural review, roof design, and snow retention work together.

Quick answer

Snow load is the weight a roof and its framing must support; snow shedding is the movement of snow and ice off a sloped roof. Illinois projects need code-based ground and roof snow inputs and a structural review, then a plan for discharge areas and possible engineered retention.

Key takeaways

  • **Snow load is structural weight; snow shedding is movement.** A roof can be strong enough for its design load yet still need a plan for falling snow and ice[2][3].
  • **Illinois is locally specific.** The Illinois Capital Development Board says local code officials provide the most accurate answers, and local amendments can matter[1].
  • **Retention is not a substitute for structure.** Snow guards transfer sliding forces into the roof and building, so the complete load path needs engineering or tested design[3][5].
  • **Plan from the ground, not from the roof.** Watch for warning signs and arrange qualified help; FEMA says unplanned snow removal can be more hazardous than beneficial[4].

What two questions hide inside the ‘can my roof handle snow’ question?

When an Illinois homeowner asks whether a metal roof can handle snow, there are two different questions hiding inside it. **Snow load** concerns gravity: the weight of snow, ice, and drifted snow that framing, connections, roof deck, and supporting walls must carry. **Snow shedding** concerns motion: whether a snowpack remains in place, melts gradually, or slides toward an eave. A roof may satisfy its design load and still discharge snow abruptly below the eave[2][3].

First establish the applicable design criteria and the existing structure’s condition. Then map discharge areas and decide whether the roof profile, layout, or an engineered retention system should control movement. A metal-only specialist can help document the roofing scope, but a roofing conversation should not replace a structural professional or the local building official when the framing, additions, drift areas, or code history are uncertain[1][3].

Snow load and snow shedding are different planning problems
QuestionWhat it addressesWho should verify it
How much weight can the roof carry?Ground and roof snow, ice, drift, framing, connections, and code criteria[2]Local code official and qualified design professional[1][2]
Where could snow and ice move?Eaves, entries, lower roofs, walkways, equipment, and property below[3][5]Roofing specialist with site-specific design review
Can retention be added?Attachment forces, roof profile, substrate, spacing, and load path[3][7]Manufacturer documentation, designer, and qualified installer
Could winter water still be a problem?Ice dams caused by roof heat flow, meltwater, and cold eaves[6]Attic/roof professionals; do not self-diagnose unseen conditions

Why isn’t there one Illinois statewide snow-load number?

Illinois homeowners should resist a single statewide snow-load shortcut. The state’s Capital Development Board explains that local jurisdictions may have codes and amendments, and that the city, village, or county code official is the best source for code questions[1]. Beginning January 1, 2025, local codes must regulate structural design at least as stringently as the applicable International Residential Code or International Building Code, but the project still needs the jurisdiction’s adopted edition and amendments[1].

The code framework treats snow as a design load, not merely a weather forecast. The Illinois structural provisions require the ground snow load to be indicated; where it exceeds 10 pounds per square foot, documents can also identify flat-roof load, exposure, importance, thermal and slope factors, and drift surcharges[2]. Those inputs vary with site, roof shape, exposure, heat, and neighboring roof levels. Ask for the governing code edition and the design assumptions rather than relying on an online map or a contractor’s informal number.

How does roof shape affect snow accumulation and drift?

Roof geometry can create uneven loading even when a weather system deposits snow across the whole neighborhood. Valleys, dormers, parapets, roof steps, adjoining additions, and lower roofs can collect drifted snow. The structural code’s requirement to account for drift surcharges where applicable reflects this uneven reality[2]. A visual roof replacement estimate may identify these features, but it cannot by itself confirm the capacity of hidden framing or a modified attic.

Before selecting a covering, document roof planes, slopes, eaves, valleys, skylights, chimneys, mechanical equipment, and lower-level roofs. Note where a falling snow slab could land: an entry, driveway, deck, sidewalk, condenser, shrub bed, or a neighbor’s property. If there is sagging, cracking, unusual movement, or a history of additions or water damage, pause and arrange an in-person evaluation by an appropriately qualified professional rather than walking on the roof.

How do metal roofs change snow shedding behavior?

A sloped metal roof may offer a smoother path for snow and ice to move than a rougher roof surface, especially during thawing and refreezing. The Metal Construction Association describes sliding snow and ice below eaves as a particular hazard on pitched roofs with slippery surfaces, and says retention systems can reduce sudden rooftop avalanches[3]. That does not mean every metal roof sheds every storm, or that stone-coated steel shingles behave exactly like a smooth standing-seam panel; surface, slope, snow condition, temperature, and roof geometry all matter.

It is whether the roof’s expected movement is compatible with the property below it. Bishop's Metal Roofing installs stone-coated steel shingles and standing-seam metal roofing as a residential metal-only specialist; the project discussion should connect the selected system and layout to the home’s actual discharge zones, without promising a particular shedding outcome.

How do snow-retention systems interact with structural snow load?

Snow guards, bars, and rails are intended to manage movement, not to make the roof structurally stronger. MCA explains that a snow-guard system is a load chain transferring sliding forces into the building structure, and that each link needs testing or engineering for the forces involved[3]. NRCA’s published abstract likewise puts the first design concern plainly: confirm the structure can support accumulated snow and ice before discussing retention devices[5].

Retention can increase friction, break up a large slide, or encourage controlled thawing, but it also adds concentrated forces and a new attachment question. The product manufacturer, roof profile, gauge, fasteners or clamps, substrate, slope, snow exposure, and site geometry all matter. A system designed for one profile should not be assumed to work on another. Request product-specific engineering or tested load information and clarify who is responsible for the design, installation, and inspection[3][5][7].

What pre-winter planning should I complete for snow and a metal roof?

A useful review begins with documents and observations: the home’s location and permitting history; adopted local code; roof framing or truss information if available; prior additions; roof slope and plane dimensions; insulation and ventilation concerns; and locations where snow discharge would be unsafe. The design professional or code official can address structural criteria, while the roofing specialist can explain the proposed roof assembly, flashing, penetrations, transitions, and compatible retention options[1][2].

What snow-load assumptions govern this project? Are drift zones present at a roof step or lower roof? Which areas need controlled retention? How will attachment forces reach framing or approved substrates? Is the proposed device compatible with this exact roof profile? What will be inspected after installation? Written answers make it easier to compare scopes and avoid treating a generic snow-guard line item as a complete engineering plan[3][7].

How are ice dams different from snow load or shedding?

Snow load and shedding do not explain every winter leak. The Insurance Institute for Business & Home Safety says ice dams form when heat warms the roof beneath snow, meltwater runs toward a colder eave, refreezes, and eventually backs water under the roof covering[6]. An ice dam can therefore involve attic heat flow and edge temperature even when the roof structure is carrying less than a severe design load.

Plan the enclosure as well as the exterior. IBHS identifies attic insulation, ventilation, and sealing ceiling openings as ways to reduce the warm-air pathway that contributes to ice dams[6]. Do not assume a metal covering alone fixes an attic problem, and do not add retention devices as an ice-dam cure without a site-specific review. Roof, attic, drainage, and flashing work should be coordinated so one improvement does not hide another problem.

What should I do during and after heavy snow to stay safe?

FEMA’s Snow Load Safety Guide says most buildings are not at risk of snow-induced failure and warns that attempting removal can be more hazardous than beneficial; it emphasizes knowing the framing system and preparing before a snow event[4]. Homeowners should monitor from safe locations for serious changes such as visible sagging, new cracks, unusual creaking, sticking doors, or displaced roof-edge components. Those signs warrant keeping people clear and calling emergency or qualified professional help, not climbing up to investigate.

After a major event, arrange an appropriate inspection if there are warning signs, known damage, or uncertainty about the structure or retention system. IBHS recommends caution around snow removal and says a wheeled snow rake from the ground can reduce scraping, while also advising professional help when needed[6]. Never approach overhead service lines, improvise tools, or walk an icy roof.

This article is general educational information for Illinois homeowners, not a structural diagnosis, code determination, engineering opinion, legal advice, or financial advice. Local code officials and qualified design or roofing professionals should review project-specific conditions. Do not climb an icy roof or attempt hazardous snow removal. Bishop's Metal Roofing states that financing is available and a 50-year warranty is stated; the current written offer and warranty control all terms.

FAQ

Snow Load vs. Snow Shedding: common questions

Does a metal roof reduce Illinois snow-load requirements?

No. Illinois provisions call for design snow loads under ASCE 7 and require relevant ground, roof, thermal, slope, and drift information in applicable construction documents[2]. A metal roof may change how snow moves, but it does not make framing stronger by itself. Confirm the adopted local code and have an appropriately qualified professional review unusual geometry, additions, deterioration, or uncertain framing before treating a roof replacement as a structural solution[1][2].

Should every Illinois metal roof have snow guards?

Not automatically. The need depends on slope, surface, snow exposure, roof geometry, and what lies below the eaves. MCA identifies sliding snow hazards on pitched slippery roofs, while NRCA says the structure’s ability to support snow and ice should be established first[3][5]. A walkway or entry may justify controlled retention even when an open lawn does not. Ask for a site-specific explanation and compatible product information rather than accepting a one-size-fits-all device or assuming stone-coated steel and standing seam will behave identically.

Do snow guards lower the roof’s snow load?

No. Snow guards manage movement; they do not subtract the weight of retained snow. MCA describes them as a load chain that transfers sliding forces into the building, and S-5! says systems should be designed to site-specific criteria[3][7]. Retention may keep snow in place longer, so the supporting structure and attachments must be appropriate for the resulting accumulation and forces. Structural review comes before retention selection, and product-specific engineering should address the exact roof profile, slope, and attachment method.

Can a metal roof prevent ice dams?

No roof covering alone can promise that. IBHS explains that ice dams form when heat from the house warms snow above the roof, meltwater reaches a colder edge, and refreezes, eventually backing water under the covering[6]. Attic insulation, air sealing, and ventilation are part of the mitigation conversation. Metal roofing can be part of a well-coordinated roof system, but it should not be sold as a substitute for correcting heat flow, drainage, or flashing problems. Have those conditions evaluated rather than guessing from the roof surface.

What should I do if I see roof sagging after a snowstorm?

Keep people away from the affected area and do not climb onto the roof or attempt improvised snow removal. FEMA warns that snow removal can be more hazardous than beneficial and emphasizes preparation and knowledge of the framing system[4]. Visible sagging, new cracks, unusual sounds, or movement should be treated as a reason to contact emergency services or an appropriately qualified structural professional, depending on the immediate risk. A roofing specialist can help coordinate an exterior inspection, but should not replace structural judgment where collapse may be possible.

References

Sources

  1. Building Codes and Regulations — Illinois Capital Development Board
  2. Chapter 16 Structural Design: Illinois Building Code 2021 — International Building Code via UpCodes
  3. Qualifying Snow Retention Systems for Metal Roofing — Metal Construction Association
  4. FEMA P-957 Risk Management Series: Snow Load Safety Guide — Federal Emergency Management Agency / WBDG
  5. Evaluating the Need for and Uses of Snow Retention Devices on Metal Roofs — National Roofing Contractors Association
  6. Ice Dams: Prevent Them and Your Roof Will Thank You — Insurance Institute for Business & Home Safety
  7. Snow Retention Systems — S-5!

Built to last. Backed by Bishop's.

Make your next roof your last.

Two metal systems, one installation standard. In a consultation we inspect the roof, explain which system fits the house, and put the scope, warranty and financing options in writing.

Schedule consultation Call now