Office: 1700 Scherer Pkwy, St Charles, MO Mon–Fri 8–6 · Sat 9–2 · Sun closed (314) 730-4080

Roof Assembly & Detailing

Coordinating Metal Roof Replacement Around Existing Skylights

Replacing a metal roof around existing skylights is a coordination decision, not a simple reroofing detail. Illinois homeowners can use this guide to review curb condition, flashing, drainage, code questions, and replacement options before work begins.

Quick answer

Coordinate the roof profile, skylight type and curb condition, flashing geometry and layers, underlayment and insulation continuity, drainage, and permit or code review before ordering materials so flashing details match the metal roof and maintain drainage.

Key takeaways

  • Treat the skylight as part of the roof system: its curb, counterflashing, surrounding panels, underlayment, and drainage all need a coordinated detail[1][3].
  • Ask whether the existing unit is curb-mounted, self-flashing, or tied to framing; the answer affects removal, replacement, and the new metal profile[3].
  • In Illinois, confirm the applicable local code path early. Chicago, for example, requires low-slope-roof skylights and other openings to comply when roof replacement occurs[4].
  • Get a written decision on reuse versus replacement, including dimensions, manufacturer instructions, flashing materials, damage allowances, and who owns any change order.

Why does an existing skylight change the roofing scope?

A skylight is a roof opening, not an accessory that can be ignored until panels are delivered. The roof covering, underlayment, curb, frame, lens, counterflashing, and nearby structure must work together to shed water. Model building-code language requires flashing around roof openings and says roof coverings are to follow both code and the manufacturer’s instructions[1]. That is why an estimate that says only “install metal roof” leaves an important transition undefined.

Start with a documented condition review from safe locations and with appropriate professional access controls. Record the skylight’s outside dimensions, curb dimensions, roof slope, panel or shingle profile, visible corrosion, signs of movement, interior staining, and whether water can drain freely above it. Do not step on a skylight or attempt an improvised roof inspection; skylights can be fall hazards, and OSHA-oriented roofing guidance treats questionable units as hazards requiring protection[3].

Skylight decision points to put in writing
DecisionWhen it may fitWhat the scope should state
Reuse existing skylightUnit, frame, curb, and flashing interface are serviceableModel or measured dimensions; curb work; compatible flashing detail; testing and exclusions[2][3]
Replace on existing curbSkylight is outdated but curb is structurally sound and compatibleNew unit requirements; curb dimensions; manufacturer instructions; interior finish responsibility[2]
Replace curb and skylightCurb is damaged, too low, out of square, or incompatible with the new roofRemoval, framing, insulation, flashing, drainage, and permit responsibilities[3][4]
Pause for further reviewHidden damage, unclear model, unusual low slope, or disputed code conditionWho investigates; what evidence is needed; no demolition assumption

How do I identify skylight type and curb before choosing flashing?

Existing units commonly differ in how they meet the roof. A curb-mounted skylight sits on a raised site-built or prefabricated curb; a self-flashing unit uses an integrated flange; other units may be installed over framing or tied closely to the deck. The distinction matters because standing seam and other metal profiles need flashing shaped to their ribs, seams, and movement. Manufacturer systems are not interchangeable by appearance alone. VELUX, for example, separates flashing systems by application and directs professionals to product-specific installation information[2].

Ask for the model, manufacturer, size, curb height, and installation instructions if they are available. If the label is gone, photographs and measured dimensions can help a contractor identify a compatible replacement, but they do not prove compatibility. A sound-looking lens does not establish that the curb, nailer, fasteners, or concealed flashing will survive removal of the old roof. The final scope should say whether the existing curb remains, is repaired, is extended, or is replaced.

What flashing layers, laps, and water directions must be reviewed?

Good flashing is a water-management sequence, not a bead of sealant. On a sloped roof, the downslope apron, side flashings, upslope backer or cricket, counterflashing, and the metal roof covering must direct water onto—not behind—the next layer. NRCA’s technical discussion compares skylight flashing to chimney flashing and describes apron, step, cricket or backer, and counterflashing functions[3]. For metal roofing, the exact folds, cleats, closures, and fasteners must follow the selected panel manufacturer’s detail.

Look for the transition points that deserve explicit notes: the top of the skylight where runoff arrives, the bottom where water accelerates, each side where lateral flow can enter a seam, and any nearby valley or roof-to-wall intersection. Illinois code guidance for residential construction calls for flashing and counterflashing at vertical surfaces and manufacturer-directed work, with corrosion-resistant metal and specified laps in covered applications[6]. The contractor should explain how the new assembly maintains drainage and accommodates thermal movement without relying on exposed sealant as the primary defense.

When is reusing a skylight sensible versus replacing it?

Reuse can be reasonable when the skylight, curb, frame, glazing, and surrounding structure are sound and a compatible flashing detail is available. Replacement deserves serious consideration when the lens is brittle or hazy, the frame is corroded, the curb is out of square, the unit has recurring condensation or leakage, or the new roof would make the old flashing impossible to integrate. A new roof can expose a weak skylight detail without causing the underlying defect; the visible symptom may appear only after the work is complete.

Do not treat “the skylight still lets in light” as a condition assessment. Ask for two written options: reuse with defined preparation and flashing work, and replacement with a specified unit, curb relationship, and interior finish responsibility. If the old curb must be raised to preserve flashing height or accommodate added insulation, that should be priced and described before authorization. NRCA notes that reroofing may require raising or temporarily removing skylights when the new assembly changes available flashing height[3].

What Illinois code or local review affects skylight work?

Illinois does not operate as one universal permit conversation for every property. The applicable jurisdiction, building type, roof slope, existing assembly, and extent of work can change the review. Chicago’s current reroofing language says flashings are to be reconstructed according to manufacturer instructions and requires skylights and other openings in the plane of a low-sloped roof to meet the cited building-code section when roof replacement occurs[4]. That is a concrete reason to ask local questions before demolition.

For a home elsewhere in Illinois, the contractor or design professional should confirm the local adopted code, permit triggers, low-slope provisions, structural concerns, and any requirements affecting skylight safety or glazing. A homeowner should not rely on a statewide blog summary or assume a neighboring municipality follows Chicago’s rule. Put permit responsibility in the contract, and keep the approval or correction record with the project file. Code compliance is a baseline; it is not a promise that an unseen roof will be leak-free.

How should drainage, insulation, and interior issues be coordinated?

A skylight interrupts continuous roof layers. Around the curb, the contractor may need to coordinate insulation continuity, air and vapor control, deck repairs, and the height of the finished roof. NRCA’s discussion warns that skylights interrupt insulation and vapor-retarder continuity and that condensation can be confused with leakage when interior humidity and cold surfaces interact[3]. This is especially relevant in Illinois, where seasonal temperature swings make roof and attic conditions change over the year.

The scope should identify who checks the attic-side evidence of staining, wet insulation, damaged framing, or condensation, and who repairs it if found. It should also explain how runoff is kept from ponding above a curb or being trapped at a seam, valley, wall, or transition. Homeowners do not need to calculate a roof assembly themselves, but they should expect the contractor to identify assumptions and exclusions rather than hide them inside a generic “weatherproof” line item.

What should a skylight flashing estimate and proposal include?

A useful proposal names the metal system, profile, underlayment, flashing metals, closure approach, fasteners, curb treatment, skylight disposition, and deck-repair allowance. It should state whether the roof is removed or recovered, how the contractor protects the opening during work, how the skylight is tested or inspected at completion, and what documentation will be provided. If a manufacturer’s detail conflicts with a field condition, the change process should be written rather than improvised on the roof.

Bishop's states a 50-year warranty, but the current written warranty controls its terms; financing is available, with the actual written offer controlling terms.

This article is general educational information, not a roof diagnosis, engineering opinion, code determination, legal advice, or financial advice. Roof access and skylight work can be hazardous; homeowners should not walk on skylights or attempt unsafe inspections. Local code, permit requirements, manufacturer instructions, site conditions, and the current written contract and warranty control. Bishop's business facts are stated separately from general evidence, and no performance, insurance, pricing, ranking, or outcome is guaranteed.

FAQ

Common questions about this topic

Can an existing skylight stay when an Illinois home gets a metal roof?

Reuse depends on the unit’s condition, curb geometry, roof slope, selected metal profile, and the availability of a compatible flashing detail. A serviceable lens does not prove that concealed flashing or curb framing is sound. The proposal should document the model or measured dimensions, curb treatment, underlayment tie-in, drainage detail, and final inspection. Chicago’s reroofing rules specifically address skylights in low-slope roofs, while other Illinois jurisdictions may apply different adopted requirements[2][4].

Should the skylight be replaced before the metal roof is installed?

A contractor may reuse a sound unit, replace only the skylight on a sound curb, or replace both curb and unit when the interface is damaged or incompatible. The important point is to decide before panels and flashings are fabricated. NRCA notes that reroofing can reduce available flashing height and may require raising or temporarily removing a skylight[3]. Ask for a written sequence that protects the opening and assigns responsibility for interior and structural work.

What should a skylight flashing estimate include?

It should identify the roof system and profile, skylight disposition, curb dimensions and repairs, underlayment, apron, side and upslope flashing, counterflashing, closures or cleats, fasteners, deck contingencies, drainage treatment, and completion checks. It should also state permit responsibility and the process for concealed damage. “Flash and seal skylight” is not enough because flashing geometry must coordinate with both the skylight manufacturer and the metal roof manufacturer[1][2].

Are skylight leaks always caused by the skylight itself?

No. Water can enter at adjacent seams, a valley, a roof-to-wall intersection, failed counterflashing, damaged underlayment, or a curb transition and then appear near the skylight inside. Condensation can also resemble a leak when cold surfaces and interior humidity interact[3]. A contractor should trace the water-management path instead of assuming the lens is the cause. Do not diagnose an unseen roof from a ceiling stain alone; request a documented inspection and clearly defined repair scope.

What makes Bishop's Metal Roofing relevant to this project?

Ask for current written warranty and financing terms; Bishop's says a 50-year warranty and financing are available, while the written documents control all terms.

References

Sources

  1. Chicago Building Code, Chapter 14R: Reroofing — City of Chicago / American Legal Publishing
  2. Chapter 15: Roof Assemblies and Rooftop Structures — International Code Council
  3. Shedding Some Light on Skylights — National Roofing Contractors Association / Professional Roofing
  4. Skylight Flashing Systems — VELUX Professional
  5. Illinois Standard for Residential Construction, Chapter 7: Roof Assemblies — ICC 600 via UpCodes
  6. Building America Best Practices Series, Volume 5 — U.S. Department of Energy, Building Technologies Office

Built to last. Backed by Bishop's.

Make your next roof your last.

Two metal systems, one installation standard. In a consultation we inspect the roof, explain which system fits the house, and put the scope, warranty and financing options in writing.

Schedule consultation Call now