Office: 1700 Scherer Pkwy, St Charles, MO Mon–Fri 8–6 · Sat 9–2 · Sun closed (314) 730-4080

Is Metal Right for My Home?

Should I Specify Metal Roofing During New-Home Design?

Quick answer

Yes—specify metal roofing during concept or schematic design rather than after framing fixes roof geometry. Early specification lets you coordinate roof pitch, drainage paths, penetrations, flashing, and manufacturer-specific assembly details in the construction documents so the AHJ can verify code compliance and installers have proper instructions.

What factors determine whether to specify metal roofing during design?

Geometry and pitch
Set roof planes, slopes, valleys, transitions, and overhangs early. Geometry determines how water reaches edges and intersections; a metal system must be selected and detailed for the actual roof, not a generic elevation[1][2].
Drainage continuity
Show gutters, downspouts, valleys, crickets, scuppers where applicable, and discharge locations as one water-management path. Building-science guidance emphasizes directing water down and out, while code addresses required drainage and overflow conditions[1][2].
Penetrations and interfaces
Locate chimneys, skylights, vents, plumbing, solar equipment, curbs, and roof-to-wall intersections before framing. Flashing is required around roof openings and changes in slope or direction; the selected system needs compatible details[1][3].
Document coordination
The architect, builder, structural designer, and roofing installer should work from coordinated drawings, specifications, submittals, and responsibilities. Standardized project documents help establish scope and connect design, engineering, construction, and closeout[4].
Evidence and approvals
Request samples, product data, tested or listed assembly information where required, approved details, installation instructions, and the AHJ permit path. Product compatibility and code acceptance should be verified for the exact proposed system[1][3].
Design-phase decisions to resolve
PhaseResolve before moving onDocumentation status
ConceptRoof forms, pitch, valleys, overhangs, and likely drainage routes[2]Design assumptions recorded
Schematic designAssembly concept, penetrations, ventilation/insulation interfaces, and structural coordination[1][3]Basis-of-design and consultant review
Permit setFlashing, underlayment, edge, drainage, and product-specific details[1][3]Code and AHJ submittal package
FramingOpenings, curbs, equipment locations, and load paths match the approved documents[1]Field coordination before covering
ProcurementExact profile, accessories, samples, product data, and approved installation instructions[3]Written submittal and ordering record

When should metal roofing and its details be documented for permits?

The locally adopted code, AHJ process, exact manufacturer instructions, and reviewed architectural and structural documents control a real project[1][2][3][4].

When metal makes sense

  • The owner and design team can commit early to a complete, compatible roof assembly and document its interfaces[1][3].
  • Roof geometry, drainage, penetrations, and framing coordination can be reviewed before construction documents are finalized[1][2].
  • The project can obtain product data, approved details, samples, and a clear local permit and inspection path[1][3].
  • The builder and installer agree in writing on submittals, sequencing, protection, and responsibility for field coordination[3][4].

When it is not recommended

  • The design team has not resolved pitch, drainage, structural assumptions, or major penetrations before framing.
  • The proposed system depends on improvised details, incompatible accessories, or a generic installation approach[1][3].
  • The AHJ path, required documents, or inspection expectations are unknown for the property[1].
  • Budget, scope, or schedule decisions require a promise that cannot be supported by a completed design and written proposal.
  • The owner wants a product name now but is unwilling to coordinate the architect, builder, structural designer, and installer.

This educational page is not a plan, engineering review, legal or code-compliance determination, permit decision, system selection, budget, schedule, or warranty promise. Confirm project-specific requirements with the design professionals, manufacturer, installer, and local AHJ.

FAQ

Should I Specify Metal Roofing During New-Home Design: common questions

When should metal roofing enter the design process?

Bring it into concept or schematic design, when roof forms, pitch, overhangs, drainage, and penetrations can still change. By the permit set, the selected assembly and its flashing, underlayment, edge, and product-specific details should be documented rather than deferred to installation[1][2][3].

Does choosing metal require a structural review?

The need and scope depend on the proposed assembly, framing design, loads, and jurisdiction. The structural designer should review the roof and its interfaces as part of the project documents; a roofing contractor should not replace required structural design or sealed review[1][4].

What should the permit set show?

At minimum, the design team should identify the roof assembly and show relevant slope, drainage, roof-to-wall, edge, valley, opening, and penetration conditions. The exact submission is controlled by the locally adopted code and AHJ, so confirm it with the building department[1].

Can the installer decide details in the field?

Some shop drawings or submittals may refine a documented design, but the field should not be the first place major geometry, drainage, structural, or compatibility decisions are made. Manufacturer instructions and coordinated project documents should guide installation and resolve responsibilities[1][3][4].

What evidence should I request before approving the system?

Ask for the exact product data, samples, installation instructions, accessory and flashing details, required test or listing information, warranty terms, and the proposed permit path. Those records let the design team and AHJ evaluate the actual assembly instead of a generic metal-roof label[1][3].

Will Bishop's select a system for my new home from this page?

No. This page explains the early decision and coordination process; it does not select a system, create plans, or promise a custom-build budget or schedule. A property-specific recommendation requires the relevant drawings, site and code review, exact product documentation, and written project scope.

References

Sources

  1. 2024 International Residential Code, Chapter 9: Roof Assemblies — International Code Council
  2. Water Management — Building Science Corporation
  3. Metal Roof Installation Manual — Metal Construction Association
  4. AIA Contract Documents: Coordinated Documents for Every Phase — American Institute of Architects

Built to last. Backed by Bishop's.

Make your next roof your last.

Two metal systems, one installation standard. In a consultation we inspect the roof, explain which system fits the house, and put the scope, warranty and financing options in writing.

Schedule consultation Call now