Office: 1700 Scherer Pkwy, St Charles, MO Mon–Fri 8–6 · Sat 9–2 · Sun closed (314) 730-4080

Standing Seam Answers

Must old cedar shakes be removed before installing standing seam roofing?

Quick answer

Not always—overlay can be permitted, but the existing shakes and deck must be assessed for deterioration, fastening support, moisture/ventilation, concealed combustible space, flashing transitions, and the panel manufacturer’s substrate instructions and locally adopted code; if these cannot be verified or corrected, tear-off is the safer path.

What factors decide if shakes must be removed?

Deck exposure and support
Cedar shakes can conceal skip or spaced sheathing, damaged boards, or irregular surfaces. A standing-seam system needs a substrate and fastening path that match its approved details; a visual roof inspection cannot establish concealed deck capacity[1][2][3].
Moisture and decay
Leaks, trapped moisture, or condensation can weaken wood beneath a new covering. USDA research describes decay above 30% moisture content, with a 20–30% gray area; investigation must be property-specific[4].
Code and combustible space
The IRC generally defines replacement as removal to the deck, but allows listed recover paths, including certain metal coverings over wood shakes. Where a concealed combustible space is created, the code calls for approved covering; the locally adopted edition controls[1].
Ventilation and drainage
NRCA identifies ventilation and drainage as replacement design priorities. A new panel system should not be treated as a cure for attic moisture, and ridge, intake, eave, or drainage changes need an assembly-level review[2].
Flashing and manufacturer details
Walls, chimneys, skylights, valleys, and edges may require new or altered flashings. Manufacturers publish deck-specific instructions rather than one universal overlay recipe, so the selected system’s current manual and accessories must be confirmed[2][3].
What assessment finds before a standing-seam decision
What is found after assessmentWhy it affects a standing-seam planAppropriate decision path
Sound, adequately supported substrate; approved recover detailPanels still need the exact substrate, attachment, underlayment, and fire requirements[1][2]Consider recover only after written manufacturer and AHJ review
Uneven shakes, weak fastener support, or deteriorated deckNRCA says degraded decks can lose fastener-holding and load capacity[2]Remove coverings and repair or replace affected deck before metal
Moisture or decay indicatorsWood decay is associated with sustained moisture; USDA identifies above 30% moisture content as a decay condition[4]Investigate the source and concealed assembly; do not cover an unresolved condition
Ventilation or flashing transition unresolvedReroofing can require direct deck access and redesigned edge, wall, penetration, or ventilation details[2]Resolve the assembly and details before selecting a panel system
Local recover, permit, or combustible-space restrictionThe IRC permits some metal coverings over shakes only under stated conditions, while local adoption and amendments vary[1][5]Confirm requirements with the authority having jurisdiction; do not generalize

How was this conclusion reached?

Overlay claims remain conditional because code adoption, deck construction, moisture, flashing, ventilation, and panel instructions vary. Site review and manufacturer details are required before a decision[1][2][3][4][5].

What should a contractor check and document after cedar shake removal?

Product suitability is not inferred across systems: instructions control.[1][6][7][8][9]

When metal makes sense

  • The existing roof is assessed, the substrate is suitable or can be prepared, and the selected manufacturer provides a compliant detail[1][3].
  • The owner is prepared to expose the assembly where needed rather than relying on an unseen deck condition[2].
  • Ventilation, drainage, and flashing transitions can be documented as part of the complete roof assembly[2].
  • The local authority accepts the proposed recover or replacement method under its adopted code[1][5].

When it is not recommended

  • The deck or shake assembly is deteriorated, water-soaked, unstable, or unable to provide reliable fastening support[1][2].
  • The project depends on concealing unresolved decay, leaks, condensation, unevenness, or drainage problems[2][4].
  • The selected manufacturer will not approve the actual substrate, recover method, accessories, or attachment path[3].
  • The local authority requires a different sequence, documentation, or removal method, or the homeowner cannot obtain that determination[1][5].

This educational page cannot determine concealed deck soundness, interpret a property’s code or permit requirements, give disposal instructions for every jurisdiction, or recommend installation over wood shakes without site-specific and manufacturer review.

FAQ

Common questions about this topic

Does the IRC always require cedar shakes to be removed?

No. The IRC’s reroofing provisions state that replacement includes removal to the deck, but also identify recover exceptions. They specifically permit metal panel, metal shingle, and concrete or clay tile over existing wood shakes when the applicable recovery provisions are met. The locally adopted code, amendments, permits, and the selected system’s instructions control; this is not a blanket approval for every house[1][5].

Can standing seam be installed directly over cedar shakes?

Do not assume so. A standing-seam system may be designed to transmit loads independently, or it may require a particular solid substrate, underlayment, nailer, or ventilation cavity. The actual panel manual—not a generic metal-roof claim—must be reviewed[3].

Why is tear-off often considered before metal?

Removal exposes the deck, lets the installer find decay or damaged boards, and permits direct preparation for underlayment, flashing, and attachment. NRCA identifies deteriorated decks, ice-dam protection, vapor-retarder needs, ventilation, and hidden conditions as reasons a recover may be inappropriate. Tear-off is therefore a condition and design decision, not an automatic judgment about every cedar roof[2].

Does cedar’s natural rot resistance make an overlay safe?

No. Cedar species and age do not establish the condition of concealed sheathing or the complete assembly. Decay depends on moisture and other environmental conditions; USDA research describes a moisture-content range in which decay risk changes. A new roof should not be used to hide an unresolved moisture source or to substitute for an appropriate assessment[4].

What should be checked at walls, chimneys, and roof edges?

The plan should account for water paths, step and counterflashing, valleys, penetrations, eaves, rakes, and any change in roof thickness. NRCA notes that flashing and edge details strongly affect reroofing performance and that existing conditions can be concealed by cladding. The selected manufacturer’s detail drawings should be coordinated with the site conditions[2][3].

Who decides whether an overlay is permitted?

The authority having jurisdiction applies the locally adopted building code and permit process; the manufacturer controls its system instructions and approvals; and a qualified roofing professional assesses the project conditions. Chicago, for example, publishes specific reroofing pathways and documentation requirements, illustrating why local rules cannot be generalized across Missouri and Illinois[5].

Why is cedar different from asphalt shingles?

Wood shakes are combustible and usually create a more irregular, thicker substrate than asphalt shingles. That affects concealed-space protection, attachment, plane uniformity, moisture assessment, and product approval. Do not transfer an asphalt-overlay answer to cedar without separate review.[1][6]

Can a metal roof hide an uneven cedar roof?

Do not assume it can. Cupped, curled, loose, or uneven shakes can affect the new system’s plane and attachment. The manufacturer may require removal or specified preparation. Site findings and written instructions control; photographs cannot establish acceptable flatness.[6][8][9]

References

Sources

  1. 2018 International Residential Code, Chapter 9 Roof Assemblies — International Code Council
  2. Steep-slope reroofing considerations — National Roofing Contractors Association / Professional Roofing
  3. New Installation Manuals and Testing for Panel Profiles — Sheffield Metals International
  4. Limiting conditions for decay in wood systems — USDA Forest Service Forest Products Laboratory
  5. Reroofing — City of Chicago Department of Buildings
  6. Retrofitting Existing Roofing with Metal — Metal Construction Association
  7. Roofing Guidelines: Reroofing — National Roofing Contractors Association
  8. Roof Guide: Cedar Shingles and Shakes — Insurance Institute for Business & Home Safety
  9. Stone Coated Steel Roofing Tiles Installation Manual — Florida Building Commission product approval archive

Built to last. Backed by Bishop's.

Make your next roof your last.

Two metal systems, one installation standard. In a consultation we inspect the roof, explain which system fits the house, and put the scope, warranty and financing options in writing.

Schedule consultation Call now