Office: 1700 Scherer Pkwy, St Charles, MO Mon–Fri 8–6 · Sat 9–2 · Sun closed (314) 730-4080

Installation

What to Check at an Electrical Service Mast Before a Metal Roof

Quick answer

Before a metal roof is scheduled, document from the ground the service mast, weatherhead, meter area, roof penetration, flashing, visible conductors, and signs of rust or movement. Then obtain written direction from the serving utility, a licensed electrician, and the AHJ on responsibilities and required records before roofing proceeds.

What determines who handles the service mast before roofing?

Responsibility boundary
Utility and homeowner responsibility can divide at the service point, while local rules add requirements. Identify the responsible party in writing before work.[2][5]
Condition and movement
A bent, loose, rusted, or displaced mast can affect electrical safety and roof weather-tightness. Document from the ground and refer repairs to an electrician.[5]
Property-specific verification
The exact roof system, surrounding construction, site conditions, and controlling manufacturer documents must be reviewed before a project-specific decision is made[1].
Visible component, coordination question, and verifier
Visible componentRoofing coordination issueResponsible verifier
Mast, conduit, or cableIs it straight, secure, visible, and suitable for the roof penetration? Do not touch it.[5]Electrician and utility
Weatherhead and service-cap areaIs the weather-tight arrangement documented? Do not infer compliance from appearance.[2][5]Utility and electrician
Roof-plane flashingObtain the exact system penetration detail and approved accessory.[3][4]Roofer; electrician confirms interface
Decision status after coordination
StatusWhat is documentedSafe planning response
Proceed to planningCoordination, AHJ path, and penetration detail are documented.[1][2][3]Roofer follows written scope; no electrical work.[3][4]
DeferResponsibility, condition, or approved detail is unclear.[2][3][5]Pause and obtain written direction.[1][2][3]

What codes and references guide mast and roof coordination?

Distances, disconnection, repairs, and permission to work near energized conductors are omitted because the adopted NEC, utility, AHJ, and professionals control them.[1][2][3][4][5]

When metal makes sense

  • Utility and electrician have documented the service arrangement and responsibilities before the roof scope is finalized.[1][2][5]
  • The selected manufacturer supplies a compatible penetration detail for the exact system.[3][4]

When it is not recommended

  • The mast or conductors show damage, movement, corrosion, or lost weather-tightness not yet evaluated by a qualified electrician.[5]
  • No party will provide written responsibility, utility coordination, or AHJ direction.[1][2]
  • The chosen system lacks an approved penetration detail or depends on field improvisation.[3][4]

Educational information only—not electrical, legal, engineering, or code-compliance advice. Do not touch service equipment or conductors; contact the utility, licensed electrician, and AHJ.

FAQ

Common questions about this topic

Can a roofer inspect or repair the service mast?

A roofer can document visible roof-interface conditions and install roofing within scope. Electrical equipment, conductors, supports, and mast repairs belong with the utility or licensed electrician. Obtain written direction before scheduling; never assign electrical work from a photograph.[1][2][5]

What should a homeowner photograph?

From a safe ground-level location, record the mast, weatherhead, meter area, roof penetration, flashing, conductors, and apparent rust or displacement. Do not climb, touch, open, measure, or manipulate equipment. Images document conditions but do not replace inspection.[5]

Does a metal roof require a special mast flashing?

It depends on the roof profile, mast configuration, and manufacturer instructions. IRC provisions require flashing around penetrations to prevent moisture entry, while product documentation identifies compatible accessories. Confirm the approved detail before materials are ordered.[3][4]

Who should be contacted first?

Start with the serving utility and a licensed electrician, then confirm the local AHJ path. The utility addresses service requirements; the electrician evaluates customer-owned components; the AHJ administers adopted code. Give the roofer that written coordination.[1][2][5]

Can the roof estimate say ‘work around the wires’?

“Work around the wires” is too vague. The proposal should identify the penetration detail, utility-coordination party, scheduling constraints, and what happens if electrical work is needed. It should not promise roofing may proceed before requirements are resolved.[1][2][3]

What if the mast is bent or the flashing leaks?

Do not straighten, seal, brace, or repair it yourself, or treat caulk as an electrical solution. Keep clear and request utility or electrician evaluation. The roofer can coordinate flashing after the electrical condition and responsibility are documented.[4][5]

References

Sources

  1. Learn More About NFPA 70, National Electrical Code — National Fire Protection Association
  2. Electric Service Requirements Manual — Rocky Mountain Power
  3. 2024 International Residential Code, Chapter 9: Roof Assemblies — International Code Council
  4. Electrical Mast Roof Flashings — Oatey
  5. Technical Focus: Service Entrance Conductors — American Society of Home Inspectors

Built to last. Backed by Bishop's.

Make your next roof your last.

Two metal systems, one installation standard. In a consultation we inspect the roof, explain which system fits the house, and put the scope, warranty and financing options in writing.

Schedule consultation Call now